Barrette Kitchen Remodeling Nationwide

Barrette Kitchen Remodeling: The Boca Raton Owner’s Guide

Barrette kitchen remodeling in Boca Raton typically runs $14,000-$45,000 for a full project, with cabinet installation, countertop replacement, and island reconfiguration as the most common component jobs. We stock and install Barrette-compatible kitchen systems, and most component replacements can be scheduled within 24-48 hours. Homeowners usually discover a problem when cabinet doors won’t stay aligned after humidity swings, drawer glides bind in the track, or laminate surfaces start delaminating near the sink where Florida’s hard water sits.

Call (754) 254-8065

Which Barrette Models This Applies To

Barrette’s kitchen product lines span three distinct eras, and identifying which one you own determines whether replacement parts are still manufactured, available aftermarket, or require custom fabrication. The pre-2015 Classic Series used a 3/4-inch overlay hinge with a 35mm cup bore, while the 2015-2022 Transitional Series switched to a soft-close Blum-style hinge with a different boring pattern. The current Haven Collection, launched in 2022, uses a fully integrated frameless system that does not interchange with earlier lines.

Check the hinge cup or drawer box for a stamped date code and model prefix. “CL” indicates Classic, “TR” indicates Transitional, and “HV” indicates Haven. If the stamp has worn off, measure the hinge cup diameter with a caliper, Classic and Transitional Series are 35mm, but the mounting plate hole spacing differs, Classic uses 45mm center-to-center, Transitional uses 52mm. We carry both OEM Barrette hardware and quality aftermarket equivalents from Blum and Salice; for Classic Series jobs in Boca Raton, we typically recommend the aftermarket route since Barrette discontinued direct support for that line in 2019.

Rowan Construction Group Boca Raton is an independent service provider, not affiliated with Barrette.

Signs Your Barrette Kitchen Remodeling Is Failing

• Doors hang crooked or won’t close flush. The hinge mounting plate loosens from the cabinet box over time, especially in Boca Raton’s coastal humidity where MDF substrate swells and screw threads lose purchase. We see this most often in kitchens west of I-95 where afternoon heat builds without the ocean breeze.
• Drawer glides stick, catch, or derail. Ball-bearing glides collect grease and salt particulate from open windows, then corrode. The Classic Series used a 75-pound-rated glide that fails under modern pot-and-pan loads; Transitional and Haven upgraded to 100-pound soft-close, but the mounting holes don’t align for direct swap.
• Laminate countertops bubble or separate at seams. Water infiltration through failed caulk attacks the particleboard substrate. In Boca Raton, this accelerates where air conditioning creates temperature differentials that expand and contract the seam daily.
• Sink base cabinet floor shows water staining or softening. The Barrette Classic sink base used a non-waterproof MDF floor with a surface seal only; once the seal cracks at a plumbing penetration, the floor deteriorates within two wet seasons.
• Island panels gap or separate from the frame. Barrette’s island systems rely on a tension-fit panel clip that loosens with seasonal movement. Homes near the Intracoastal with higher humidity variance see this first, usually on the side facing the afternoon sun.

Before

After

Replacement Cost & What’s Included

Component-level Barrette kitchen work in Boca Raton breaks down as follows:

• Cabinet installation (per unit or linear foot scope): $4,000-$13,000
• Countertop installation (including templating and sink cutout): $2,000-$6,500
• Backsplash installation (tile or solid surface): $800-$2,500
• Kitchen island installation (relocate, reconfigure, or replace): $3,000-$10,000
• Small kitchen remodel (partial replacement, same footprint): $9,000-$20,000
• Full kitchen remodel (layout change, new cabinets, countertops, appliances): $14,000-$45,000

What drives the range: material grade (Barrette Haven Collection runs 40% above Classic-equivalent finishes), structural modifications (moving plumbing or electrical), and whether we encounter substrate damage requiring repair before new installation. Under Clause 1 of the Haven Standard, your written quote includes every line item, parts, labor, and permit fees, before anyone picks up a tool. No change proceeds without a signed change order. Every project carries our 365-Day Done Right Promise, backed by a terms page, not an asterisk.

DIY or Call Us?

There’s honest work a homeowner can do: tighten a loose hinge screw with a #2 Phillips, clean drawer glide tracks with degreaser, or re-caulk a countertop seam with 100% silicone. These are maintenance, not repair, and they buy time.

Where DIY goes wrong: hinge plate re-boring into swollen MDF (the screw holes strip and the plate sits proud, ruining door alignment), glide replacement on face-frame cabinets (the mounting hole math is unforgiving, and a 1/8-inch error accumulates across a bank of drawers), or countertop templating (Barrette’s specified overhangs assume specific base cabinet depths that vary by series). We’ve been called to three Boca Raton jobs this year where a homeowner’s DIY glide replacement left drawer fronts that racked so badly the boxes had to be rebuilt. Measure twice, document everything, then build. If you’re past the maintenance stage, call (754) 254-8065 and we’ll schedule a free estimate with a written price before any work starts.

FAQs